Quick Start

First Calibration

On this page

This page takes you through your first calibration. You need FoCal installed and your licence set up first:

Contents of this page

What you need

  • Your camera and the lens you want to calibrate.
  • A USB cable to connect the camera to your computer. One usually comes with the camera.
  • A sturdy tripod.
  • A FoCal target: a FoCal hard target (supplied with boxed FoCal, or from the FoCal Store), or a target image printed on good-quality paper.

Fix the target to a flat, vertical wall, at a height you can easily aim the camera at on its tripod.

The distance from the camera to the target matters. If the camera is too close, the calibration won't suit general shooting as well. FoCal shows the recommended minimum distance for your lens in Target Setup and in the Target Distance Tool. Some examples:

Focal Length Recommended Minimum Distance
16mm 0.8m (2 feet 7 inches)
24mm 1.2m (3 feet 11 inches)
50mm 2.5m (8 feet 2 inches)
70mm 3.5m (11 feet 5 inches)
200mm 5.5m (18 feet)

The camera also needs to be close enough to your computer for the USB cable to reach. With a laptop this is rarely a problem; with a desktop computer, keep it in mind when you choose where to calibrate. We don't recommend USB extension cables unless you have no choice: in our experience they can make the connection unreliable.

Lighting

Calibration makes sure your camera's autofocus and your lens work together as well as possible. For that, the autofocus system needs plenty of light on the target.

FoCal checks the light level before each test, so choose a location to start with and check it with Target Setup (see below).

A well-lit room works best. If FoCal warns that the light level is too low, add a constant light source pointed at the target. Avoid fluorescent and cheap LED lights: they can flicker and upset the calibration.

We don't recommend calibrating outdoors. Wind can move the setup, and clouds can change the light level during the test.

Camera and lens

Put the camera on a sturdy tripod, pointing at the target from the right distance. If you normally use a battery grip, remove it: it can increase vibration and reduce the quality of the results.

Look through the viewfinder and roughly line up the centre focus point with the centre circle of the target. It doesn't need to be perfect: Target Setup warns you if it's too far off.

Connect the USB cable to the camera and the computer.

On a DSLR, cover the viewfinder eyepiece for the best results. When you're shooting, your head blocks light from entering the viewfinder. During a FoCal test it doesn't, and stray light can upset the camera's metering.

Some cameras have a built-in eyepiece shutter, and some have an eyepiece cover on the strap. If yours has neither, hang a piece of dark paper over the back of the camera.

Camera and lens settings

FoCal controls the camera and changes most settings itself. Check these before you start:

  • Canon: set the mode dial to Av and the AF mode to ONE SHOT.
  • Nikon: set the mode dial to A and the focus mode to AF-S.
  • Turn off image stabilisation, if your lens or camera has it.
  • Turn off the focus limiter, if your lens has one.

Checklist

  • The camera is on a sturdy tripod, with no battery grip.
  • The USB cable connects the camera to the computer.
  • The eyepiece is covered (DSLR).
  • The target is on a flat, vertical wall, at the right distance from the camera.

Connect your camera

The screenshots are from Windows, but the steps are the same on a Mac. Everything on this page works in FoCal Plus and FoCal Pro.

With everything in place, start FoCal.

Open the Camera menu and choose Status to go to the Camera page:

Turn the camera on. It appears in the Available Cameras panel. If it doesn't, click the refresh button next to the Available Cameras title.

The Serial Number / License Info column shows the camera's serial number and whether it has been added to your licence. A camera FoCal hasn't seen before shows a question mark (License state unknown) until you connect to it.

Click Connect. FoCal takes a shot, and after a few seconds it shows information about the camera and lens:

If FoCal shows Connect & Restore instead of Connect, the camera was disconnected part-way through an earlier test. Click it to put your camera's settings back: see If the Camera Disconnects.

Check your setup with Target Setup

Before calibrating, check that FoCal is happy with your setup. On the Camera page, click Open on the Target Setup card (or choose Camera › Target Setup):

Target Setup opens:

The Recommended Target Distance panel shows the minimum distance between the camera and target for your lens. Don't worry too much about it: Target Setup tells you if the camera is too close.

Click Start.

Target Setup takes a photo and checks whether your setup is suitable for calibration. The results appear in the Environment Check Results panel, and a Live View image helps you adjust the position.

Problems are marked with Some text Some more or . Click an entry to see more information:

Entries marked are things FoCal can't check itself. Read the details and make sure the item is set as described.

If there are problems, adjust your setup, then click the refresh button next to the Environment Check Results title.

When there are no Some text Some more or entries, your setup is ready. Click Finish Checking to stop Target Setup.

Run the calibration

Choose Camera › Focus Calibration (or click Open on the Calibration card on the Camera page):

You've already checked your setup, so click Start.

With a Hands Free Mode camera, FoCal runs the whole calibration by itself. With a User Assisted Mode camera, FoCal asks you to change the AF fine-tune value on the camera from time to time:

Set the value on the camera, then click Continue (or press Return). Once you know FoCal better, Voice Prompts and the Camera Hotkey make these changes quicker: see User Assisted Mode (UAM).

Autofocus. Fixed.

When the test finishes, FoCal shows the calibration result:

Drag the slider on the image to compare the before and after images, check the quality values, and click Accept if you're happy with the result.

The test's tabs give more information: Summary, and in FoCal Pro Details (all the numbers and charts), Compare (how your result compares with other users of the same camera and lens, using FoCal Comparison Data) and History (your previous tests).

Your camera is now adjusted to work as well as possible with this lens. You can close FoCal, disconnect the camera and go out shooting sharper photos.

What next?

Calibration gets you sharp. A Kit Health Check keeps you there: calibrate, then run FoCal's other tests while you're set up. Do it monthly if you can, because the more results FoCal has, the sooner it spots a change in your kit, or confirms it's still performing well. At the very least, do it every three months. With FoCal Pro, Kit Status and Analysis (in the History menu) show how each camera and lens is holding up over time. See FoCal Setup Checklist.